
Can Lifts Operate During Fires? Safety Rules
A fire alarm activates, occupants begin moving toward exits, and someone asks whether the elevator can still be used. The answer to “can lifts operate during fires” is not a simple yes or no. A lift may still have power and be mechanically capable of moving, but normal passenger use is generally restricted once the fire emergency system is activated. The system is designed to remove elevators from public use, return them to a safe landing, and reserve controlled operation for trained emergency responders.
For property owners and facilities teams, the distinction matters. Treating an operating car as a safe evacuation route can expose occupants to smoke, heat, loss of power, or entrapment. Treating every fire signal as a lift failure can also lead to incorrect troubleshooting and unnecessary downtime. The correct response depends on the building’s fire alarm sequence, elevator controls, emergency power arrangement, and instructions from the authority having jurisdiction.
Can Lifts Operate During Fires? Normal Use vs. Emergency Use
In most commercial and residential buildings, elevators are not intended for general occupant evacuation during a fire. Stair enclosures are the primary means of egress unless the building has a specifically engineered occupant evacuation elevator system and a documented emergency plan for its use.
When smoke detectors associated with the elevator system initiate a fire emergency recall, the elevator controller typically removes the car from normal service. It travels to a designated recall floor, opens its doors, and remains unavailable to ordinary users. If smoke is detected at that primary recall floor, the car should instead travel to an alternate recall floor. This reduces the risk of opening elevator doors onto a smoke-affected lobby.
The lift has therefore “operated” during the incident, but it has not remained available for public transport. That difference is central to safe building procedures. A car moving automatically to a recall landing is performing a protective function, not offering a route for occupants to leave the building.
A manually operated fire service mode may be available after recall. This mode is for authorized firefighters and other trained emergency personnel, not building staff or occupants. It gives responders direct control of car movement and door operation under defined conditions. It does not make the elevator inherently safe in every fire scenario.
What Happens When Fire Recall Is Activated
Fire recall is commonly described in two stages. The precise controls and required interfaces depend on the applicable elevator and fire codes, the local authority having jurisdiction, and the building design. Facilities teams should confirm the sequence for each site rather than assume all lifts behave alike.
Phase I: Automatic Emergency Recall
Phase I starts when the designated smoke detector, fire alarm system, or approved manual control activates the elevator recall function. The controller cancels registered calls, prevents normal hall-call operation, and directs the car to the primary recall level. If the primary level is affected by smoke detection, the controller selects the alternate level.
A properly maintained installation also needs to handle practical conditions at the landing. The car should not remain at a floor where doors could open into a hazardous area. If a door is obstructed or a component fault prevents the expected sequence, that condition needs prompt investigation after the event. Fire recall testing is not simply a test of the lift controller. It verifies the interaction among detectors, fire alarm controls, wiring interfaces, elevator equipment, and landing conditions.
Phase II: Firefighter Operation
Phase II begins when an authorized responder uses the in-car fire service controls after the elevator has recalled. The car is operated manually, typically requiring continuous pressure on controls for travel and door movement. This intentional operation helps responders assess conditions rather than allowing the car to respond automatically to calls.
Firefighter operation has limits. Responders may decide not to use the elevator if water is entering the shaft, smoke is migrating into the car or lobby, electrical equipment is compromised, or the fire location creates unacceptable risk. Elevator use during a fire remains a tactical decision directed by the incident commander and emergency procedures, not a convenience for building operations.
Why an Elevator Can Become Unsafe So Quickly
An elevator shaft is a vertical opening through a building. Depending on the fire scenario, it can be affected by smoke movement, heat, water, and loss of electrical supply. The main risk is not only that the car stops. A passenger may be delivered to a hazardous floor, trapped between levels after a power interruption, or exposed to smoke entering through doors or shaft openings.
Water is another critical factor. Firefighting activity, sprinklers, and burst pipes can affect hoistway equipment, pit components, landing doors, and electrical circuits. Modern protective features can reduce some risks, but no feature eliminates the need for trained assessment. After a fire event, a lift should be inspected before being returned to normal service, even if it appears to operate normally.
This is especially relevant for goods lifts, hydraulic lifts, platform lifts, and industrial lifting systems. Their duty, controls, shaft configuration, and operating environment may differ from those of a standard passenger elevator. A warehouse goods lift near stored materials, for example, should be assessed against its specific fire strategy and operational hazards. The same principle applies to marine and industrial installations where emergency procedures may be governed by additional site or vessel requirements.
Emergency Power Does Not Mean Public Use Is Allowed
Many building teams assume that an elevator connected to emergency or standby power can be used during a fire. That is not necessarily correct. Emergency power is often provided so selected elevators can be recalled, positioned, or made available for emergency response. It may also support elevators specifically designed for evacuation under an approved building strategy.
Generator capacity is usually limited. The system may sequence cars one at a time, prioritize fire pumps and life-safety equipment, or restrict operation to designated elevators. A loss of normal power can also change the elevator’s behavior before the generator is fully online. These details should be reflected in the building’s emergency operating procedure and tested as part of planned maintenance and life-safety testing.
Do not rely on a sign, a generator, or the fact that elevator lights remain on as proof that a lift is available for evacuation. The approved fire strategy, current alarm condition, and fire department direction take priority.
Requirements for Building Owners and Facilities Managers
The practical objective is not to decide during an emergency whether elevators are safe. That decision should already be built into the site’s fire plan, elevator configuration, and staff training.
First, confirm that each elevator has correctly defined primary and alternate recall floors. Changes to lobby layouts, tenant fit-outs, fire alarm devices, or access arrangements can affect whether those floors remain suitable. Second, maintain the interface between the fire alarm system and elevator controls. A lift contractor may maintain the elevator equipment, while another specialist maintains fire detection and alarm equipment. Clear responsibility for testing the interface is essential.
Third, train security, reception, and facilities personnel on what they should and should not do. They should know how to recognize recall, keep passengers from using the cars, communicate with emergency responders, and report any abnormal car position or door condition. They should not attempt to override fire service controls or reset systems without authorization.
Finally, arrange a competent post-incident inspection. This should cover controller faults, door operation, shaft and pit conditions, water exposure, traveling cables, landing equipment, and any fire alarm interface issues. Returning a lift to service without inspection can turn a contained incident into a later reliability or safety failure.
Design and Modernization Considerations
For new developments and major modernization work, fire emergency operation should be reviewed early. It affects recall-floor selection, smoke detector locations, controller programming, emergency power provisions, communications, and coordination with the overall fire strategy. It is far more efficient to resolve these interfaces during design than after commissioning reveals a conflict.
Older installations deserve particular attention. A modernization project may improve controller reliability, door protection, communications, and code alignment, but the fire recall function must be evaluated as part of the complete building system. Replacing an elevator controller without validating detector inputs, recall logic, emergency power behavior, and documented test results leaves a significant gap.
Lift Dynamics supports installation, modernization, repair, and maintenance across passenger, goods, platform, hydraulic, industrial, and custom lift systems. For fire-related operation, the priority is always the same: equipment configuration must align with the approved building fire strategy and be maintained by competent personnel.
When a fire alarm occurs, occupants should use the prescribed exit route, not make a judgment based on whether an elevator appears to be running. The time to verify recall settings, emergency power behavior, and responder procedures is during planned testing, while the building is calm and every safety-critical system can be checked properly.




Comments